Homemade Pool Deck

homemade deck pool

We’ve been getting a lot of requests to write an article on how to build a DIY pool deck around an above-ground pool since we released All About Above-Ground Pools a few months ago. To get the most out of your pool experience, you’ll need a location to rest and sunbathe near to the pool. Most people believe that making a DIY pool deck is an impossible endeavor, but it isn’t at all. Custom above-ground pool courses can be given a chance by experienced workers who have built many pools using DIY manuals.

In terms of scope, it’s a massive undertaking, but it’s not difficult to put together and doesn’t necessitate the expertise of an expert. Good lumber, an essential woodworking skillset, and the right tools are all you need to get started—the size of the deck extra joists by the size of the pool and your preferences. Small and large decks use the same basic principles, but the materials and work required are different.

  1. Preparing The Ground By Digging Holes And Erecting Stakes

Ground preparation is the first step in any DIY pool deck construction project. To prepare for your construction site, remove all grass and dirt at least 2 inches deep. We utilized 4 x 4 lumber for the posts, and we strongly advise against using anything smaller. The first step is to lay down four boards on the ground to understand how your deck will look. Remove the boards and mark the areas where the posts will go. 

You can use a post-hole digger to excavate holes that are somewhat larger than the posts themselves. Keep in mind that the depth of your holes must be at least 3.5 feet to avoid freezing. Place the seats in the gaps, level them, and fill them with rock sand. Once you’re halfway there, secure the post on each side with four heavy boulders. Then, fill the rest of the hole with rocks. Concrete can also be used, but this method is just as strong. Apply a waterproof wood sealant to the buried portion of each post to prevent rotting.

deck pool

  1. Building The Skeleton Of A Diy Pool Deck Frame.

After all of the posts are in place, the framing can begin. We utilized 2 x 6 boards for the beams and joists, and we strongly advise against using smaller lumber. Take four 2 x 4s and use them to secure and level the corner posts before building the frame. When the beams are screwed into place, they are no longer needed and removed. For your beams to be leveled appropriately, both ends of the shaft extra joists installed joists must be tightened. 

Use a tiny piece of wood and screw it to the post below the beam’s specified height. Then, place the beam’s end on the part of the wood and screw it into place. You’ll find it much easier to level the beam this way because you’re only aligning one end of the beam. Beams outside the pool must be the same height, while those within are 6 inches shorter. It is time to fasten all the posts and lay the weed barrier and stone beneath your new deck. If you wait until after the deck is built, it will be challenging to get under it.

deck pool

  1. Build The Stairs And Secure Posts.

Build a staircase for your deck now. You’ll need two 2 x 12 stringers, seven 2 x 6 risers, six 2 x 8 runners, one 2 x 6 for the top runner, and two 4 x 4 stair posts for that project. Mount the stair stringer brackets on the beam, build the risers, and run to 6 inches and 8 inches, respectively. Depending on the size of your staircase, separate the stringers. Put 4 x 4s at the end of both stringers and secure them to the stringers with two smaller holes.

Temporarily fasten the upper ends of the posts using 2 x 6 boards before beginning the joists. This will ensure that the structure does not shift while joists are being installed. Because beams now support the building, you can remove the posts.

deck

  1. Joist Installation And Post Trimming

To have a perfectly level deck, you’ll need to care extrajoists now support the building when installing the joists. We used 2 x 6 planks for the beams and added corner brackets to attach them. Because the shape of a pool determines the length of each joist, you must measure the length of each post. To get an accurate measurement, subtract 2 inches from the distance because you’ll be connecting the beams to the pool using boards. A solid deck requires at least one beam every 20 inches. We put a joist on each side from every post and block between the joists to provide additional security. As an extra safety precaution, we used corner brackets to hold the beam at each corner.

Because the posts aren’t at the same height, they may be too high. The size of your railing must be determined and marked on a stick. To replicate this height, they utilize a 2×4 and a level to move it to additional positions. Top and bottom rails are made of 2x4s, which They may cut to any height. An aluminum railing can be added if desired.

deck

  1. Railings And Decking.

Decking is the final step in any DIY pool deck project. 5/4 x 8,  5/4 x 6, or 5/4 x 10 wood can be used for decking. Because it looks nicer, we utilized 5/4 x 6 decking boards. As a first step, fasten one × four panels around the pool’s edge, making sure to fill up any gaps thoroughly. Then, working your way toward the pool, begin laying 5/4 x 6 boards. 

To cut the right shape out of the 1 x 4 boards, you’ll have a little bit of difficulty. Aligning the 5/4 x 6 board to the head of the 1 x 4 board is the trick. Then, crawl that under the deck and use a pen to draw a line to cut the board. Make sure to screw each board into each joist utilizing wood screws before beginning the process of building a deck. To prevent cracking and splitting, start by drilling a hole just slightly smaller than just the screw’s diameter. Finish the stairs by adding the risers and runners after the decking is done.

The railing is the final step that needs to be completed. When it comes to the finishing touches, this is a matter of personal preference. We ended the project using 1 x 2 spindles every 6 inches with 1 x 4 boards over top of the railing.

In addition to building your pool deck, you may also make other budget-friendly garden ideas, such as deck chairs and an umbrella. Glass deck railings offer an air of refinement and class to your home’s exterior.

deck

  1. The Last Touches

Now that you’ve completed your DIY pool deck, you won’t be adding much to the cost of your pool at all. Inflatable hot tubs can now be added as the last touch. Companies like EmerGenie can provide outside plumbing if your collection isn’t close enough to your house and you don’t want to mount a hose every time you want to replenish it.

Make a gate for your kids if you have them. Our instruction on making a DIY little fence gate will help you if you’re not sure how to build the gate on your own. If you want your deck to last, you must cover the deck and the fence with a waterproof wood sealant.

There are several birds you’re likely to observe on your pool deck: Robins, sparrows, blackbirds, starlings, and mourning doves. These are magnificent animals that play a vital role in the natural world. Pressure washing the pool deck is a chore that many people don’t have time for when spending time outside. Also, swimming through a pool full of floating bird droppings is the awful feeling ever. 

It’s therefore imperative that once you’ve completed your DIY Pool deck, should find a solution to remove these pests from your property. Otherwise, your time spent outside will suffer. To dissuade birds from pooping on your deck and pool, you can hang mirrors, spin pinwheels, and use plastic predator birds or ultrasonic sound systems to deter them. To discover more about how these strategies function, you’ll need to conduct a thorough study.

deck

In addition to building your pool deck, you may also make other budget-friendly backyard concepts, such as deck chairs and an umbrella. For those who enjoyed creating your pool deck, you may want to check out ideas for a DIY hot tub.